Sunday, February 7, 2016

How To Hack Wifi password WPA/WPA2 WPS in Windows

How To Hack Wifi password WPA/WPA2 WPS in Windows OS
How To crack Wifi password WPA/WPA2 WPS in Windows

What is WPA/WPA2 :
Wi-Fi Protected Access (WPA) and Wi-Fi Protected Access II (WPA2) are two security protocols and security certification programs developed by the Wi-Fi Alliance to secure wireless computer networks. The Alliance defined these in response to serious weaknesses researchers had found in the previous system, WEP (Wired Equivalent Privacy). WPA (sometimes referred to as the draft IEEE 802.11i standard) became available in 2003. The Wi-Fi Alliance intended it as an intermediate measure in anticipation of the availability of the more secure and complex WPA2. WPA2 became available in 2004 and is a common shorthand for the full IEEE 802.11i (or IEEE 802.11i-2004) standard. A flaw in a feature added to Wi-Fi, called Wi-Fi Protected Setup, allows WPA and WPA2 security to be bypassed and effectively broken in many situations. WPA and WPA2 security implemented without using the Wi-Fi Protected Setup feature are unaffected by the security vulnerability. WPA2 has replaced WPA. WPA2, which requires testing and certification by the Wi-Fi Alliance, implements the mandatory elements of IEEE 802.11i. In particular, it includes mandatory support for CCMP, an AES-based encryption mode with strong security. Certification began in September, 2004; from March 13, 2006, WPA2 certification is mandatory for all new devices to bear the Wi-Fi trademark.

What Is WPS :
Wi-Fi Protected Setup (WPS; originally Wi-Fi Simple Config) is a network security standard that attempts to allow users to easily secure awireless home network but could fall to brute-force attacks if one or more of the network's access points do not guard against the attack.

Download Dummper

Download JumpStart

Download WinPcap

Microsoft .NET Framework ( if required )

Follow these instructions for How To crack Wifi password WPA/WPA2 WPS in Windows:
  1. Download and install JumpStart, WinPcap, and Dumpper
  2. Open Dumpper. It’ll be in Spanish, so go to the far right tab and select ‘English’ in between the other two options.Your programs are set up and ready to go, now begin the process:
  3. In the ‘Networks’ tab, select the network adapter you wish to use. Hit the ‘Scan’ button now.
  4. After it completes the scan, go over to the ‘Wps’ tab. In the area that says ‘Connect using JumpStart’, hit ‘Browse’ to select the location of where you installed JumpStart in the previous set-up steps. (By default, it installs in C:\Program Files (x86)\Jumpstart. Don’t open it, just select the ‘Jumpstart’ folder and click ‘OK’)
  5. In the area ‘Show default pin’, select ‘All networks’ isntead of ‘Only known networks’.
  6. Hit the ‘Scan’ button.
  7. Select the network you wish to penetrate. Remember the ‘Pin’ corresponding to your network in the scan results, this will be needed for later.
  8. In the previous area ‘Connect using Jumpstart’, hit the ‘Start JumpStart’ button.
  9. Under ‘What do you want to do?’, select ‘Join a wireless network’ and hit ‘Next’
  10. Under ‘Which setup method do you want to use?’, select “Enter the PIN from my access point” and enter the PIN next to your network in the scan section back in the previous scan results.
  11. Finally, select the targeted network from before and hit ‘Next’.Now you’re happily connected to that WiFi network you just penetrated. Do you want to see the password so you can get on from other devices without doing this process? Sure! Follow these simple steps:
  12. Open the menu where you join WiFi networks/view the network you’re connected to.
  13. Right click on the network you just joined and hit ‘Properties’
  14. Under the ‘Security’ tab, you can see the password, but it’s just dots. Check the ‘Show characters’ box under it.
  15. The password will then reveal itself.

No comments:

Post a Comment